.:HSTuners::

95DX · 06-09-2004, 04:36 AM

how low can a 95 Civic be lowered before a camber kit would be needed I asking so I know wether (sp?) to get a camber kit or not before I have the suspention done

ebpda9 · 06-09-2004, 07:13 AM

rule of the thumb is 1.5" but it depends on how worn or straight your suspension components are

95DX · 06-10-2004, 12:11 AM

ok thanks I haven't gotten the suspention but I wanted to know for when I get it

06-21-2004, 08:16 AM

I put those Eibach lowering springs and the Koni Yellows on...I can't remember what the drop was/is but I think I need something to maintain control...what does the camber kit do?

95DX · 06-29-2004, 12:02 AM

when you lower your car your wheels move usually outward (I believe) the camber kit would allow your wheels to be corrected to what the specs are supposed to be (as to place your wheels as if your car were at stock hight) ie if you have ever seen someone driving a baja bug and the tires (usually the back) look like / \ the camber kit would allow the tires to go back to l l if that makes any sence well when you lower your car you tend the have the same basic problem just not as obvious (hope this makes sence I know what Im saying but I dont know that Im wording it right)

07-03-2004, 08:19 PM

Ok...i don't have that problem so I guess I wouldn't need a camber kit then...

95DX · 07-03-2004, 11:40 PM

depending on how "big" your drop is you might its going to depend on what they say when you go for an alignment

07-04-2004, 02:53 PM

See, my drop wasn't even that big...the most was maybe 2 inches...

95DX · 07-06-2004, 02:19 AM

what are good brands for camber kits and would you only need it for the front only or would you need it for all 4 wheels (looking on ebay out of curiosity and saw some for what looked like 2 wheels only and some for all 4)

ebpda9 · 07-06-2004, 07:40 AM

well the best brands will be skunk2, spc, ingalls. any other than that are not that great.

95DX · 07-06-2004, 08:56 PM

ok thanks now would I need it for front only or all 4 wheels

autocrossthugg · 07-07-2004, 05:19 AM

I would recomend that you get the full set of 4. That way there won't be any wierd wear on the tires.

ebpda9 · 07-07-2004, 07:13 AM

spc makes a nice kit for the rear too. i would do all 4 wheels but i would let 1.5 degrees of negative camber on the rear. i noticed both of my cars hadndle better that way

95DX · 07-07-2004, 02:55 PM

ok thanks

95DX · 07-11-2004, 04:18 AM

ok a few more questions then I think Im done, where can I find spc adjusters other then exospeed.com and maybe ebay. approx what would they cost (didn't see any price on exospeed.com and found only 1 result on ebay and it was $375 which seems a little high to me) and would something like this be worth buying http://cgi.ebay.com/ebaymotors/ws/eB...category=33583 and are these only for the rear or are they available for the front too

ebpda9 · 07-11-2004, 09:49 AM

well those are more for show and they allow a bit of the unsprung weight reduction. the cast iron stock arms are quite heavy. i think they are worth it but i don't know how well they are done, and how close to stock dimensions they are.

95DX · 07-12-2004, 03:45 AM

thats what I was kinda thinking as far as show/looks I would probably see if I could find something like that for a little cheaper but not too cheap. any ideas for how much/were I could find 4 wheel spc kits at? I figure I'd go one company for the whole thing

ebpda9 · 07-12-2004, 05:56 PM

i don't carry spc, but i can get the skunk2's for the front. a very nice kit and very easi to adjust, plus look pretty sturdy and i haven't noticed for them to bottom out

07-21-2004, 02:27 AM

how much are u selling the skunk2s front camber?

anyone know any other sites that are selling camber kits for a good low price?

ebpda9 · 07-21-2004, 06:22 AM

right now i can do 205 shipped + 8% sales tax

06-09-2004, 04:36 AM	#1
95DX 2nd Gear Join Date: Jul 2003 Location: no longer Cal or AZ now in Pa at least until Feb Posts: 189	camber kit question how low can a 95 Civic be lowered before a camber kit would be needed I asking so I know wether (sp?) to get a camber kit or not before I have the suspention done

06-09-2004, 07:13 AM	#2
ebpda9 Repost Wagon Join Date: Dec 2001 Location: over here Age: 44 Posts: 17,266	rule of the thumb is 1.5" but it depends on how worn or straight your suspension components are __________________

07-06-2004, 07:40 AM	#10
ebpda9 Repost Wagon Join Date: Dec 2001 Location: over here Age: 44 Posts: 17,266	well the best brands will be skunk2, spc, ingalls. any other than that are not that great. __________________

07-07-2004, 05:19 AM	#12
autocrossthugg 2nd Gear Join Date: Mar 2003 Location: McKinleyville CA. Age: 59 Posts: 205	I would recomend that you get the full set of 4. That way there won't be any wierd wear on the tires. __________________ Ground Control Coil-overs Eibach springs Tokico Struts(Illumina front & HD rear) Suspension Techniques Anti-Sway Bars (f&r) SPC Camber Kits (f&r) Front Upper Strut Bar Rear Lower Bar Borbet Type B rims w/Falken Azenis for autocross Kosei K-1 rims w/Yokohama AVS-ES100 for street 3-point Sparco Harness

07-07-2004, 07:13 AM	#13
ebpda9 Repost Wagon Join Date: Dec 2001 Location: over here Age: 44 Posts: 17,266	spc makes a nice kit for the rear too. i would do all 4 wheels but i would let 1.5 degrees of negative camber on the rear. i noticed both of my cars hadndle better that way __________________

06-10-2004, 12:11 AM	#3
95DX 2nd Gear Join Date: Jul 2003 Location: no longer Cal or AZ now in Pa at least until Feb Posts: 189	ok thanks I haven't gotten the suspention but I wanted to know for when I get it

06-21-2004, 08:16 AM	#4
Kool-Aid Posts: n/a	I put those Eibach lowering springs and the Koni Yellows on...I can't remember what the drop was/is but I think I need something to maintain control...what does the camber kit do?

06-29-2004, 12:02 AM	#5
95DX 2nd Gear Join Date: Jul 2003 Location: no longer Cal or AZ now in Pa at least until Feb Posts: 189	when you lower your car your wheels move usually outward (I believe) the camber kit would allow your wheels to be corrected to what the specs are supposed to be (as to place your wheels as if your car were at stock hight) ie if you have ever seen someone driving a baja bug and the tires (usually the back) look like / \ the camber kit would allow the tires to go back to l l if that makes any sence well when you lower your car you tend the have the same basic problem just not as obvious (hope this makes sence I know what Im saying but I dont know that Im wording it right)

07-03-2004, 08:19 PM	#6
Kool-Aid Posts: n/a	Ok...i don't have that problem so I guess I wouldn't need a camber kit then...

07-03-2004, 11:40 PM	#7
95DX 2nd Gear Join Date: Jul 2003 Location: no longer Cal or AZ now in Pa at least until Feb Posts: 189	depending on how "big" your drop is you might its going to depend on what they say when you go for an alignment

07-04-2004, 02:53 PM	#8
Kool-Aid Posts: n/a	See, my drop wasn't even that big...the most was maybe 2 inches...

07-06-2004, 02:19 AM	#9
95DX 2nd Gear Join Date: Jul 2003 Location: no longer Cal or AZ now in Pa at least until Feb Posts: 189	what are good brands for camber kits and would you only need it for the front only or would you need it for all 4 wheels (looking on ebay out of curiosity and saw some for what looked like 2 wheels only and some for all 4)

07-06-2004, 08:56 PM	#11
95DX 2nd Gear Join Date: Jul 2003 Location: no longer Cal or AZ now in Pa at least until Feb Posts: 189	ok thanks now would I need it for front only or all 4 wheels

07-07-2004, 02:55 PM	#14
95DX 2nd Gear Join Date: Jul 2003 Location: no longer Cal or AZ now in Pa at least until Feb Posts: 189	ok thanks

07-11-2004, 04:18 AM	#15
95DX 2nd Gear Join Date: Jul 2003 Location: no longer Cal or AZ now in Pa at least until Feb Posts: 189	ok a few more questions then I think Im done, where can I find spc adjusters other then exospeed.com and maybe ebay. approx what would they cost (didn't see any price on exospeed.com and found only 1 result on ebay and it was $375 which seems a little high to me) and would something like this be worth buying http://cgi.ebay.com/ebaymotors/ws/eB...category=33583 and are these only for the rear or are they available for the front too

07-11-2004, 09:49 AM	#16
ebpda9 Repost Wagon Join Date: Dec 2001 Location: over here Age: 44 Posts: 17,266	well those are more for show and they allow a bit of the unsprung weight reduction. the cast iron stock arms are quite heavy. i think they are worth it but i don't know how well they are done, and how close to stock dimensions they are. __________________

07-12-2004, 03:45 AM	#17
95DX 2nd Gear Join Date: Jul 2003 Location: no longer Cal or AZ now in Pa at least until Feb Posts: 189	thats what I was kinda thinking as far as show/looks I would probably see if I could find something like that for a little cheaper but not too cheap. any ideas for how much/were I could find 4 wheel spc kits at? I figure I'd go one company for the whole thing

07-12-2004, 05:56 PM	#18
ebpda9 Repost Wagon Join Date: Dec 2001 Location: over here Age: 44 Posts: 17,266	i don't carry spc, but i can get the skunk2's for the front. a very nice kit and very easi to adjust, plus look pretty sturdy and i haven't noticed for them to bottom out __________________

07-21-2004, 02:27 AM	#19
beretta92r Posts: n/a	how much are u selling the skunk2s front camber? anyone know any other sites that are selling camber kits for a good low price?

07-21-2004, 06:22 AM	#20
ebpda9 Repost Wagon Join Date: Dec 2001 Location: over here Age: 44 Posts: 17,266	right now i can do 205 shipped + 8% sales tax __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode