.:HSTuners::

*pdiggitydogg* · 12-04-2005, 08:40 PM

Im really interested in doing something to reduce the amount of air getting trapped in the rear bumper to cut down on drag.
Not as a speed mod, to increase mpg (slightly).

NO, Im not cutting holes.....

So, who can make something like this?

Only...not so damn gargantuan

I have almost zero fabrication skills and wouldnt know where to get a sheet of aluminum anyway...what about expanding foam (if kept away from the muffler)?

V8killimports · 12-04-2005, 08:49 PM

I would suggest not making a large lifting surface in the rear of your car

*AzCivic* · 12-04-2005, 10:17 PM

EG gas savers had this, maybe you can do something with it?

*pdiggitydogg* · 12-04-2005, 10:28 PM

yeah, vx
There really isnt a place for that to bolt up on the ek

sicones · 12-05-2005, 07:37 AM

I tried buying a piece of sheet aluminum like that last summer that shit is expensive, some tin snips and some sheet metal screws, that thing doesn’t look that hard to make, though I would try to bolt it to some factory locations

*pdiggitydogg* · 12-05-2005, 09:12 AM

the real problem is that it would have to be perfect, or else it would catch even more air than before

C's 94 InTeGrA · 12-05-2005, 11:39 AM

Theres a couple sites on www.evolutionm.net who makes those. I aint sure if they make them for any car but they do for my car

*pdiggitydogg* · 12-05-2005, 11:48 AM

Do you have a direct link? All I saw in their marketplace was classified ads for used parts and then apparel in the store.

Im sure they dont have anything for hondas, but Id like to see what they came up with for evo's

*AzCivic* · 12-05-2005, 11:51 AM

you should take a real good pic of the underside of your car like the one you posted, just so we can see if it'd be easy to do.

*pdiggitydogg* · 12-05-2005, 11:54 AM

pff...not with snow on the ground sir
even my garage floor is soaking wet from melted snow
So, theres a job for someone with an ek in a warmer climate

*AzCivic* · 12-05-2005, 12:54 PM

weeny!

*pdiggitydogg* · 12-05-2005, 01:03 PM

lol yep!

thermal · 12-06-2005, 12:03 AM

I can make that shit. I just dont think it is worth the time and effort enough to make a difference tho. Functionality wise, putting holes on your rear bumper will probably be better..... but I'm not really into that kind of mods....

I enjoy fabricating stuff. When I get back, I will fab up my own traction bar.

Pat, all those parts and tools can be found on your nearest Home Depot or Lowes........

*pdiggitydogg* · 12-06-2005, 12:36 AM

I called both home depot's and they dont carry sheet metal of any kind

V8killimports · 12-06-2005, 08:07 AM

First of all I would suggest using sheet aluminum... and something with like a 1/16" thickness that can be bent and cut easily but not flimsy. You can cut this easily with almost anything, but a $80 band saw would work well... I have one. It would be easy to make with MINIMUM fab skills.. only thing that would be a pain is all the measuring and fitting. ... just tedious.

And the metal you can get at any metal supplier... you just have to do a search on yahoo yellow pages.. took me a while to find one, and they typically sell in HUGE quantities, but the place I found gives me all their scraps if I want including stainless... and their scraps can be as large as 3x3'.

C's 94 InTeGrA · 12-12-2005, 03:37 PM

in the evom sponsor list first category. damn i lost the link if it pops back up for them ill hit u up

12-04-2005, 08:40 PM	#1
pdiggitydogg Yahoo Watashi wa kattaze! Join Date: May 2002 Location: Meanwhile, up in The D... Age: 41 Posts: 10,579	reducing rear drag Im really interested in doing something to reduce the amount of air getting trapped in the rear bumper to cut down on drag. Not as a speed mod, to increase mpg (slightly). NO, Im not cutting holes..... So, who can make something like this? Only...not so damn gargantuan I have almost zero fabrication skills and wouldnt know where to get a sheet of aluminum anyway...what about expanding foam (if kept away from the muffler)?

12-05-2005, 11:39 AM	#7
C's 94 InTeGrA 4th Gear Join Date: Jan 2002 Location: Dover, Ohio Age: 39 Posts: 858	Theres a couple sites on www.evolutionm.net who makes those. I aint sure if they make them for any car but they do for my car __________________ 2003 Apex Silver Mitsubishi Evolution 8

12-06-2005, 12:03 AM	#13
thermal Banning Machine Join Date: Aug 2001 Location: My Garage, Va. Posts: 5,547	I can make that shit. I just dont think it is worth the time and effort enough to make a difference tho. Functionality wise, putting holes on your rear bumper will probably be better..... but I'm not really into that kind of mods.... I enjoy fabricating stuff. When I get back, I will fab up my own traction bar. Pat, all those parts and tools can be found on your nearest Home Depot or Lowes........ __________________ Project Teg Visit the Turbo Forum

12-12-2005, 03:37 PM	#16
C's 94 InTeGrA 4th Gear Join Date: Jan 2002 Location: Dover, Ohio Age: 39 Posts: 858	in the evom sponsor list first category. damn i lost the link if it pops back up for them ill hit u up __________________ 2003 Apex Silver Mitsubishi Evolution 8

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-04-2005, 08:49 PM	#2
V8killimports Registered User Join Date: Sep 2002 Location: Beale AFB, CA Posts: 1,377	I would suggest not making a large lifting surface in the rear of your car

12-04-2005, 10:17 PM	#3
AzCivic Moderator Join Date: Feb 2002 Location: Az Age: 43 Posts: 3,804	EG gas savers had this, maybe you can do something with it?

12-04-2005, 10:28 PM	#4
pdiggitydogg Yahoo Watashi wa kattaze! Join Date: May 2002 Location: Meanwhile, up in The D... Age: 41 Posts: 10,579	yeah, vx There really isnt a place for that to bolt up on the ek

12-05-2005, 07:37 AM	#5
sicones Registered User Join Date: Apr 2003 Location: the MVP garage, New York City Posts: 516	I tried buying a piece of sheet aluminum like that last summer that shit is expensive, some tin snips and some sheet metal screws, that thing doesn’t look that hard to make, though I would try to bolt it to some factory locations

12-05-2005, 09:12 AM	#6
pdiggitydogg Yahoo Watashi wa kattaze! Join Date: May 2002 Location: Meanwhile, up in The D... Age: 41 Posts: 10,579	the real problem is that it would have to be perfect, or else it would catch even more air than before

12-05-2005, 11:48 AM	#8
pdiggitydogg Yahoo Watashi wa kattaze! Join Date: May 2002 Location: Meanwhile, up in The D... Age: 41 Posts: 10,579	Do you have a direct link? All I saw in their marketplace was classified ads for used parts and then apparel in the store. Im sure they dont have anything for hondas, but Id like to see what they came up with for evo's

12-05-2005, 11:51 AM	#9
AzCivic Moderator Join Date: Feb 2002 Location: Az Age: 43 Posts: 3,804	you should take a real good pic of the underside of your car like the one you posted, just so we can see if it'd be easy to do.

12-05-2005, 11:54 AM	#10
pdiggitydogg Yahoo Watashi wa kattaze! Join Date: May 2002 Location: Meanwhile, up in The D... Age: 41 Posts: 10,579	pff...not with snow on the ground sir even my garage floor is soaking wet from melted snow So, theres a job for someone with an ek in a warmer climate

12-05-2005, 12:54 PM	#11
AzCivic Moderator Join Date: Feb 2002 Location: Az Age: 43 Posts: 3,804	weeny!

12-05-2005, 01:03 PM	#12
pdiggitydogg Yahoo Watashi wa kattaze! Join Date: May 2002 Location: Meanwhile, up in The D... Age: 41 Posts: 10,579	lol yep!

12-06-2005, 12:36 AM	#14
pdiggitydogg Yahoo Watashi wa kattaze! Join Date: May 2002 Location: Meanwhile, up in The D... Age: 41 Posts: 10,579	I called both home depot's and they dont carry sheet metal of any kind

12-06-2005, 08:07 AM	#15
V8killimports Registered User Join Date: Sep 2002 Location: Beale AFB, CA Posts: 1,377	First of all I would suggest using sheet aluminum... and something with like a 1/16" thickness that can be bent and cut easily but not flimsy. You can cut this easily with almost anything, but a $80 band saw would work well... I have one. It would be easy to make with MINIMUM fab skills.. only thing that would be a pain is all the measuring and fitting. ... just tedious. And the metal you can get at any metal supplier... you just have to do a search on yahoo yellow pages.. took me a while to find one, and they typically sell in HUGE quantities, but the place I found gives me all their scraps if I want including stainless... and their scraps can be as large as 3x3'.