.:HSTuners::

09-16-2002, 12:37 AM

So I am looking at replacing my Cams. I got the Type R cams in there now. Running a bored B18c1 (2.0 now) and 11.5:1 pistons. I want to stay all motor and I need recommendations for the new bump sitcks. I was looking at the Toda or Skunk2 ones stage 3 on either. I really don't care all that much about the fuel consumption or idle, so that's not a deciding factor, more toward mid and hi end power. Any recommendations? Oh, Anyd I am going to get the Skunk2 ECU in a month, so I need something that goes with that (should be running lo 13's then)

95 GSR
2.0 B18C1
Skunk2 Intake manifold
AEM CAI
DC 4-2-1 header
11.5:1 pistons
JUN flywheel
Stage 2 clutch
HKS Hiper exhaust

09-16-2002, 07:36 AM

i say go Skunk2....i have heard alot of good things about them...haven't heard too much about Toda...although what i did hear was positive...but i still say go with Skunk2...just my 2 cents though

2ndGenTeg · 09-16-2002, 04:20 PM

No way. Todas ROCK. If it were me, that's what I would get.

Toda is one of those names not everyone knows, but those that know swear by. Toda is arguably the best B eries cam on the market. If it were me, I'd get the Toda Spec Bs, unless you have an 11K redline.

Also look at the Jun Stage 2s. Both are very comparable. Juns will have a little more high end power, but the Todas have a little more mid range and are easier to tune.

You don't need an ecu tune, but it would help a great deal, especially with aftermarket cams. Truthfully, a V-AFC will probably take care of all your needs, including:
Redline move or elimination
VTEC crossover
A/F adjustment

09-16-2002, 12:37 AM	#1
dudeman47 Posts: n/a	95 GSR cams So I am looking at replacing my Cams. I got the Type R cams in there now. Running a bored B18c1 (2.0 now) and 11.5:1 pistons. I want to stay all motor and I need recommendations for the new bump sitcks. I was looking at the Toda or Skunk2 ones stage 3 on either. I really don't care all that much about the fuel consumption or idle, so that's not a deciding factor, more toward mid and hi end power. Any recommendations? Oh, Anyd I am going to get the Skunk2 ECU in a month, so I need something that goes with that (should be running lo 13's then) 95 GSR 2.0 B18C1 Skunk2 Intake manifold AEM CAI DC 4-2-1 header 11.5:1 pistons JUN flywheel Stage 2 clutch HKS Hiper exhaust

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-16-2002, 07:36 AM	#2
crx swap Posts: n/a	i say go Skunk2....i have heard alot of good things about them...haven't heard too much about Toda...although what i did hear was positive...but i still say go with Skunk2...just my 2 cents though

09-16-2002, 04:20 PM	#3
2ndGenTeg 4th Gear Join Date: Aug 2001 Location: Boulder, CO Age: 44 Posts: 830	No way. Todas ROCK. If it were me, that's what I would get. Toda is one of those names not everyone knows, but those that know swear by. Toda is arguably the best B eries cam on the market. If it were me, I'd get the Toda Spec Bs, unless you have an 11K redline. Also look at the Jun Stage 2s. Both are very comparable. Juns will have a little more high end power, but the Todas have a little more mid range and are easier to tune. You don't need an ecu tune, but it would help a great deal, especially with aftermarket cams. Truthfully, a V-AFC will probably take care of all your needs, including: Redline move or elimination VTEC crossover A/F adjustment