.:HSTuners::

IALuder · 08-15-2006, 12:34 AM

I just wanted to know when you clock the turbo you are only turning the comp housing side right?I did that to a point to where it could reach my hotpipe but I need to turn the center section aliitle bit so it would be easier for the oil and coolant lines to reach I just wanted to know how would you turn the center section, I just don't want to fuck it up.Any advise would be great

JDMFantasy2k · 08-15-2006, 08:58 AM

yeah you can clock both sides, and is usually a good idea to do so that way the oil outlet is facing straight down, depending on the manifold you're using.

Just remember when you're clocking loosen the bolts a little and turn slow. There's a gasket (on t3's anyway) between the backing plate and the comp housing and you don't want to wreck it. The turbine side you don't have to worry about except make sure you torque the bolts in sequence so the turbine wheel sits level in the housing. Spin the comp wheel by hand afterward just to be sure nothing is rubbing.

thermal · 08-16-2006, 12:40 PM

Wd40 Ftw

IALuder · 08-16-2006, 01:27 PM

it has 6 bolts to hold the housing, and a big snap ring also on the cold side. so do i just take the snap ring off and loosen the bolts on each side to turn the center?

thermal · 08-16-2006, 08:08 PM

You shouldnt have to take the snap ring off. The snap ring should be for the inner housing.... but then again, it just depends on what turbo

08-15-2006, 12:34 AM	#1
IALuder Registered User Join Date: Sep 2003 Location: Des Moines IA Age: 38 Posts: 7,908	clocking I just wanted to know when you clock the turbo you are only turning the comp housing side right?I did that to a point to where it could reach my hotpipe but I need to turn the center section aliitle bit so it would be easier for the oil and coolant lines to reach I just wanted to know how would you turn the center section, I just don't want to fuck it up.Any advise would be great __________________ 93 Si H23vtec......soon to be 12lbs 95 Civic EX....automatic DD if you cant dazzle them with your brillance, baffle them with your bullshit.

08-15-2006, 08:58 AM	#2
JDMFantasy2k Registered User Join Date: Mar 2004 Location: northeastern connecticut Age: 37 Posts: 1,765	yeah you can clock both sides, and is usually a good idea to do so that way the oil outlet is facing straight down, depending on the manifold you're using. Just remember when you're clocking loosen the bolts a little and turn slow. There's a gasket (on t3's anyway) between the backing plate and the comp housing and you don't want to wreck it. The turbine side you don't have to worry about except make sure you torque the bolts in sequence so the turbine wheel sits level in the housing. Spin the comp wheel by hand afterward just to be sure nothing is rubbing. __________________

08-16-2006, 12:40 PM	#3
thermal Banning Machine Join Date: Aug 2001 Location: My Garage, Va. Posts: 5,547	Wd40 Ftw __________________ Project Teg Visit the Turbo Forum

08-16-2006, 01:27 PM	#4
IALuder Registered User Join Date: Sep 2003 Location: Des Moines IA Age: 38 Posts: 7,908	it has 6 bolts to hold the housing, and a big snap ring also on the cold side. so do i just take the snap ring off and loosen the bolts on each side to turn the center? __________________ 93 Si H23vtec......soon to be 12lbs 95 Civic EX....automatic DD if you cant dazzle them with your brillance, baffle them with your bullshit. Last edited by IALuder : 08-16-2006 at 01:30 PM.

08-16-2006, 08:08 PM	#5
thermal Banning Machine Join Date: Aug 2001 Location: My Garage, Va. Posts: 5,547	You shouldnt have to take the snap ring off. The snap ring should be for the inner housing.... but then again, it just depends on what turbo __________________ Project Teg Visit the Turbo Forum

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode